How to choose the direction of opening the door? What problems should you pay attention to when choosing the direction of opening the door?

The direction of opening the door cannot be arbitrarily specified, because there are many problems that need to be paid attention to when choosing the direction of opening the door. Then, how to choose the direction of opening the door? What problems should be paid attention to when choosing the direction of opening the door? The problem that needs to be paid attention to when opening the door? Let's go:

The direction of opening the door is divided into four directions: inner left, inner right, outer left and outer right (except for sliding doors); firstly, according to your own habits, the direction of the hand is selected first; after opening the door, the door can not block the traffic line entering the room; after opening the door The wall of the door that is blocked by the door leaf may not have a circuit panel for switching the indoor light; the door leaf should be fully open and should not be blocked by furniture; the door leaf after opening should not be close to the heating, water source and fire source; the opening direction of the door leaf should be relatively spacious. Note that the door should not be bumped with the water table, the cabinet, etc.; the grounding installation position of the door leaf should be reasonable, do not hinder the furniture placement or obstruct the indoor traffic line; if the door is conditional, it must be opened outward.

First, the door installation process

The effect of the door lock installation directly affects the usability and safety of the door, so every detail of the door lock installation cannot be ignored. Although many home decoration doors are now installed by specialized teachers, consumers should also know more about the installation of the doors to prevent safety hazards caused by construction workers. Let's look at the basic process and acceptance of the door installation.

Second, measure whether the door and door hole are suitable

Measure the thickness of the wall, the width and height of the door hole, and then measure the length of the top frame and the length of the frame of the finished door frame to see if it is suitable for the door opening.

Third, the assembly of the door frame

The three frame doors are on the same plane, the top frame and the frame are connected at a 90-degree angle, and 4 to 6 pieces are fixed on both sides of the frame, and the lock legs and the locking angle strips are nailed, and the top frame is covered on both sides. Above, the inner width of the two frame door should be 7mm larger than the door width, and the inner height between the top door door and the ground should be 13mm higher than the door height.

Fourth, install the door frame

Put the assembled door frame into the door hole as a whole, check whether it is vertical, connect the nail hole as a point, determine the position of the nail hole on the wall, fix the connecting piece to the wall with the element nail, and crevice in the door frame and the wall Inlaid into the wooden strip, the door frame and the wall are firmly connected.

Fifth, install the door hinge

When installing the door hinge, first screw a screw on the upper and lower hinges, close the door to check whether the gap is suitable, check whether the door and the door are on the same plane, ensure that the door is consistently good, the door is not falling, and the other screws are tightened after correct. . It is not allowed to screw the screw directly into the frame of the entry. When installing the door frame and the door leaf, ensure that the door door is consistently good. The door leaf and door lock switch are flexible, the gap around the door leaf is consistent, the connection gap is tight and firm, and the decorative surface is not damaged.

Six, the installation line

The installation of the line can be determined according to the width of the wall and the door frame. If the wall is narrower than the frame, the side with the width of the line can be used against the wall. If the frame is narrower than the wall, the cover line can be removed on both sides of the line. The line is fixed with the nail and the back cover can be returned.

Seven, quality acceptance method after installation

1. Look at the gap: the seam of the wooden sealing line, the corner line and the waist line decorative panel should not exceed 0.2mm, the angle between the line and the line clamping mouth should not exceed 0.3mm, the veneer and the plate mouth should not exceed 0.2mm, and the sliding door should be full. The error does not exceed 0.3mm.

2, look at the structure: whether the structure is straight. The correct carpentry practice should be straightforward, whether horizontal or vertical.

3, look at the corner: whether the corner is accurate. Normal corners are all 90 degrees, with the exception of special design factors.

4, look at the mosaic: whether the mosaic is strict and accurate. Proper wooden parquet, to be seamless or to maintain a uniform separation distance.

5. Look at the arc: Whether the curvature and roundness are smooth and smooth. In addition to a single, multiple identical shapes also ensure consistent shape.

6. Look at the door leaf: Is the door leaf switch normal? When the door leaf is open, it should be light and no sound.

7, look at the level: should ensure that the surface of the woodworking project is flat, no drums or broken.

Global hardware network

Concerned about surprises

Label: How to choose the direction of opening the door? What problems should you pay attention to when choosing the direction of opening the door?

Previous: How to extend the life of forklift clutch release bearing? Next: What is semiconductor material? How to define semiconductor material

ECO Solvent Canvas

Inkjet Polyester Canvas,Inkjet Print Canvas,Inkjet Printing On Canvas,Art Prints Canvas

Guangzhou Quanxu Technology Co Ltd , https://www.skychema.com